You are here: IndustrialPartner.com / Industrial Computers / Industrial Computers / BVM

BVM

Choose a product:

Breakout-1 - Free standing or panel mounting breakout module SCSI II style 50 way input to 8 9pin D connectors SIO4 or SIO8 DIO32 or DIO64 CTR32 or CTR64

Breakout-2 - Paddle board connecting CompactPCI J3 and J4 to two SCSI II style 50 way connectors Provides facilities to apply +5V or ground to unassigned pins on the SCSI connectors cPC2PMC dual PMC carrier SIO4 and SIO8 SCU2 and SCU2a

BVME065 - SRAM/Flash/EPROM 3U VMEbus module Three banks of 4x32 pin JEDEC sockets for up to 6Mb battery backed SRAM, 3Mb Flash, 12Mb EPROM, arranged as 3 bank of 4 devices, each bank can be individually set for access speed, device type, base address, Flash program driver for OS-9

BVME130 - Floppy / SCSI Controller- 3U Supports most floppy disc formats including 4Mbyte perpendicular recording. SCSI supports most common command set drives with data rates to 3.3Mbytes/sec. 68440 DMAC, dual ported SRAM buffer

BVME210 - Digital I/O module 32 bit I/O, 8 configurable handshake lines, 2x68230 PI/T chips, Centronics interface, polled or interrupt mode, 2 independent timers, on or off board timer control, cable termination and system conditioning modules available

BVME227 - IEEE488/GPIB Controller - 3U Advanced IEEE488/GPIB Controller supporting IEEE488.2 extensions, uses TMS9914A, 68440 DMAC. Double buffering allows simultaneous VMEbus and GPIB accesses with minimum CPU overhead

BVME250 - Analogue input module - 3U 12 Bit A/D 16 differential or 32 single-ended inputs, full scale input voltages from 20mV to 20 Volts, link or S/W selectable. 11µs worst case conversion

BVME290 - Watchdog Timer/System Module - 3U Watchdog Timer/System Monitor with standby battery supply, selectable watchdog timeout SYSFAIL monitor, ACFAIL monitor, Power monitor for supply rails, 8 external alarm inputs, 2 output alarm relay contacts, 16-bit status register holding alarm conditions, battery back-up supply feeding +5Volt VMEbus standby line, Reset/enable keyswitch

BVME3000 - 68360 6U VMEbus SBC with IndustryPack™ I/O 32MHz up to 16Mb 32bit wide DRAM, 512Kb dual-ported SRAM, 1 or 2Mb boot sector Flash, 6 serial ports RS232/422/485/Ethernet, 8/16bit parallel port, 4 counter/timers, 4x32pin memory expansion sockets, 4 IndustryPack sites 8/32MHz with DMA

BVME305 - Counter Timer - 3U Ten independent 16 bit timers with externally accessible gate control, source control and output lines, four vectored interrupts, uses AM9513 devices

BVME310 - 68000 3U VMEbus Processor 10MHz, 512K/2Mbyte SRAM, 2 x 28 pin EPROM sockets, 128bytes EEPROM, RTC, dual RS232 serial ports, system controller

BVME3100 - 68360 6U VMEbus Communications Controller 32MHz, 2Mb BOOTFLASH, 2Mb SRAM, 8Mb DRAM, 6 serial channels, 1 with ETHERNET option, 1 with ISDN option, RS232/422/485, 16 character alphanumeric display on front panel, VMEbus Master/Slave Interface, Background Debug Port

BVME3500 - Dual 68360 Communications 6U SBC 32MHz up to 8Mb 32bit wide DRAM, 512Kbor 2Mb non-volatile SRAM, 1 or 2Mb boot sector Flash, 11 serial ports RS232/422/485/Ethernet, 10baseT Ethernet port, 4 IndustryPack sites via EXP100 expansion module, Background Debug Port

BVME363 - 68010 6U VMEbus Processor Module 12.5MHz, 512Kbyte dual ported RAM, 4 x 28 pin EPROM sockets 68451 MMU opt. 68230 dual 8 bit parallel ports and timers, dual RS232 serial ports, system controller

BVME370/380 - 68030/68EC030 3U VMEbus SBC 40MHz, 68882 FPU, 4Mb DRAM, burst fill cache, dual RS232/422/485 ports, printer port, sockets for 512Kb EPROM, RTC, Mailbox interrupts, watchdog timer, 128bytes non-volatile RAM

BVME390/395 - 68040/EC040 3U VMEbus SBC 25MHz includes FPU dual 4K caches. 32Mb dual ported snooped DRAM 16Mb FLASH, 256K battery backed SRAM, 1MB EPROM, dual RS232/422/485 ports, RTC, mailbox interrupts, printer port, watchdog timer, 128byte EEPROM system controller and bus arbiter functions. VME interrupter and handler

BVME4000 - 68040 6U VMEbus SBC with IndustryPack I/O - BVME4000 33MHz up to 512Mb dual ported DRAM, 64Mb FLASH, 512Kb or 2Mb battery backed SRAM, 2Mb EPROM, dual RS232/422/485, parallel printer port, SCSI with DMA, Ethernet with on-board cheapernet and drop cable interfaces, dual IndustryPack sites expandable to six, I/O paddle boards compatible with other manufacturers SBCs (e.g. MVME162)

BVME410 - Ethernet Controller - 3U Uses LANCE Chipset, high performance 256Kbytes dual ported SRAM buffer. On-board drop cable and coax connectors. Extensive software support

BVME4500 - 68040 3U VMEbus CPU with Ethernet 33MHz up to 512Mb dual ported DRAM, 64Mb FLASH, 2Mb battery backed SRAM, 2Mb 32 bit wide Boot sector Flash, 2Kbit EEPROM, dual RS232 ports, 10 baseT Ethernet, ruggedised 3U VMEbus format

BVME6000 - 68060 6U VMEbus SBC with IndustryPack I/O - BVME6000 50MHz up to 512Mb dual ported DRAM, 64Mb FLASH, 512Kb or 2Mb SRAM, 2Mb EPROM, dual RS232/422/485, parallel printer port, SCSI controller with DMA, Ethernet with on-board cheapernet and drop cable interfaces, dual IndustryPack sites expandable to six, I/O paddle boards compatible with other manufacturers SBCs (e.g. MVME172)

BVME650 - Data Acquisition Analogue I/O Board - 3U 32 single ended or 16 differential inputs, 4 channel DAC, 12 bit resolution, 16K or 64K option bytes of dual ported SRAM, DMA, automatic channel sequencing, programmable gain and conversion rates

BVME681 - Disc Modules - 3U or 6U Family of Disc Modules containing BVME130 controller, floppy and SCSI drives. Plugs directly into the VMEbus and requires no external cabling. 2 or 4Mb floppy, up to 240Mb SCSI disc

BVME770 - Intelligent Octal Serial Controller - 6U RS232/422, on-board 68000 processor with up to 512Kbytes of dual ported SRAM, HDLC or SDLC, DMAC, VMEbus system controller, synch/asynch firmware available

BVME771 - Intelligent Quad Serial Controller - 3U Four async/sync RS232/422/485 using Z8530, 68HC001 CPU 16MHz, 64Kb dual ported SRAM, 256Kb EPROM

BVME772 - Intelligent Quad Serial Controller - 3U Four async/sync RS232/422/485 ports using 85C230 68HC001 CPU 16MHz. 256Kb dual ported SRAM 256Kb EPROM, RTC, battery-backed SRAM

BVME775 - 68010 6U VMEbus Comms Processor 16MHz 2Mb dual ported SRAM, 68450 DMAC 4 x 32 pin EPROM/SRAM sockets, 8 RS232/422 ports with on board drivers, RTC, VME interrupter and handler. System Controller

BVME795 - Graphics Display Module - 3U Graphics Display Controller featuring Hitachi ACRTC, 1024 x 768 screen resolution, drawing speeds up to 2 million pixels/sec. 4/8 bit CLUT, 512/1024K VRAM. (BVME795/6/7)

cPC1000 - CompactPCI Desktop or Portable System Enclosure Economical portable or desktop system enclosure providing four CompactPCI slots (optionally up to eight if disc drives are not required) with mounting for floppy disc, hard disc and CD drives. Powered by an auto-sensing 300Watt PC ATX power supply it has ample power for most applications and is fully compliant with hot swap requirements. All parts are fabricated from aluminium to ensure light weight whilst maintaining strength and good shielding properties. It is designed to be fully compliant with CE directives on EMC and LVD

cPC200 - cPCI SBC with Graphics Accelerator and Ethernet and PMC Site CompactPCI SBC blade with AMD K6, K6-2, K6-3 133-550MHz, mobile Pentium 266MHz, 66-100MHz Super Socket 7, 512Kb Pipelined Burst Cache 100MHz, 512MB SDRAM (ECC option), 32 bit 33MHz PCI 2.1 compliant, ACPI support, Savage 4 Graphics Adapter via AGP bus, 8 or 32MB SDRAM, 3D Accelerator, CRT of LCD (via PanelLink), PMC expansion site, 10baseT/100baseTX Ethernet via front panel RJ45, PS2/AT keyboard/Mouse sockets, two 16550 compatible UARTS with 16 byte FIFO and IR, parallel port supporting ECP, EPP, PS2, SPP and IEEE1284, 2.88Mb Floppy disc controller, IDE with Ultra 33 DMA support, tri-stateable driver for drive bay swap, hub with three USB ports 12MB and 1.5MB/sec, Hot plug event detection, Standby and suspend wake up events including RTC alarm and Modem ring, 2Mbit single voltage Flash device BIOS EPROM. Software support includes Windows NT, NT Embedded, XP Embedded, 95, 98, 2000, VxWorks, Linux etc.Compact PCI v2.1, Hot Swap v1.0

cPC2PMC - Hot Swap dual CompactPCI PMC Carrier CompactPCI Hot Swap Dual PMC Carrier, compatible with cPCI Hot Swap specification 2.1 R1.0, Uses Texas Instruments PC12250 33MHz 32bit PCI bridge conforming to PCI local bus specification 2.2, PMC rear I/O via J3 and J4, 3.3 or 5 Volt signalling. Full hot swap support under Windows 2000 and XP Embedded

cPC2PMC-E - CompactPCI dual PMC Carrier CompactPCI Dual PMC carrier. A straightforward carrier for economy applications not requiring hot swap or advanced de-bug features. An ideal choice for volume production applications but maintaining compatibility with the other modules in the cPC2PMC family

cPC2PMC-T - Hot Swap dual PMC Carrier for Telco Applications CompactPCI Hot Swap Dual PMC Carrier, the same as cPC2PMC but with the rear I/O from the PMC sites routed to J3 and J5 instead of J3 and J4. This alternative pinout is compatible with systems using H110 backplanes

cPC2PMC64(-T) - cPCI Hot Swap dual PMC Carrier 64Bit / 66MHz CompactPCI dual PMC carrier for 64-bit / 66MHz hot-swap applications. Uses the latest HB6 bridge chip from HiNT ensuring full compliance with PICMG 2.1 R2.0 with PI = 1 support

IP-302 - Intelligent Communications Controller The IP-302 is a general purpose IndustryPack ™ compatible module built around a 68302 Integrated Multi-protocol Processor. It features an on-board RS485 port, fully opto-isolated with transient suppression, operating over two/four wire asynchronously/synchronously. Speeds of up to 2 Mbits/second are achievable. The IP-302 is optimised for use as a gateway into BVM’s FieldLink distributed fieldbus network but it finds many applications in other communication areas where the microcode of the 68302 offers many advantages. In addition two further serial ports, two counter timers, a watchdog timer and 28 digital I/O lines are available as unbuffered TTL levels allowing the user to implement signal conditioning on an external transition module as required. Communication with the host IndustryPack ™ carrier is via the Dual Ported SRAM which also holds the code for its firmware. The code for the firmware is downloaded following system boot up. A comprehensive debug environment is available for use with OS-9 hosts

IP-ADC - A-D Converter with High Accuracy and Opto-isolation The IP-ADC is a cost effective IndustryPack ™ compatible module providing sixteen analogue input channels which can be either differential or single ended. By careful design the component count in the front end has been kept low ensuring a minimum of induced noise and very low temperature drift. The IP-ADC uses the AD7890 12 bit converter from Analogue Devices. This is fed by a sixteen channel multiplexor and instrumentation amplifier. The 11mS conversion times allow sustained conversion rates of over 90kHz on a single channel. The on-board precision voltage reference has very low drift characteristics ensuring continued accuracy over a broad range of operating environments. This reference can also be fed back to one of the input channels to provide a temperature compensation facility. Versions of the IP-ADC are available providing inputs of 0-5, 0-10Volt or 0-20 mA. A comprehensive driver for OS-9 is available providing field calibration facilities and also the option of data sampling to minimise noise effects in difficult environments

IP-IN20 - Opto-isolated Input / Output Modules The IP-IO20 family of cost effective IndustryPack ™ compatible modules providing twenty opto-isolated I/O connections. Three configurations are available as standard providing 20 input, 20 output or 10 input and 10 output respectively. Isolation of 2.5KVolts is maintained between any two I/O points and the IP bus enabling it to be used in a number of demanding applications. Each input will operate with an input current as low as 2ma. With the standard input resistors input voltages of up to 50Volts can be applied allowing the IP-IO20 to be directly connected to plant wiring. Each input line can be programmed to interrupt on change of state. The output lines are individually fed via solid state relays which provide isolation from line to line and from the logic interface. Each output is able to drive up to 100ma continuously with a power rating of 125mW. For more demanding applications extended environmental specification modules are available

IP-IO20 - Opto-isolated Input / Output Modules The IP-IO20 family of cost effective IndustryPack ™ compatible modules providing twenty opto-isolated I/O connections. Three configurations are available as standard providing 20 input, 20 output or 10 input and 10 output respectively. Isolation of 2.5KVolts is maintained between any two I/O points and the IP bus enabling it to be used in a number of demanding applications. Each input will operate with an input current as low as 2ma. With the standard input resistors input voltages of up to 50Volts can be applied allowing the IP-IO20 to be directly connected to plant wiring. Each input line can be programmed to interrupt on change of state. The output lines are individually fed via solid state relays which provide isolation from line to line and from the logic interface. Each output is able to drive up to 100ma continuously with a power rating of 125mW. For more demanding applications extended environmental specification modules are available

IP-OUT20 - Opto-isolated Input / Output Modules The IP-IO20 family of cost effective IndustryPack ™ compatible modules providing twenty opto-isolated I/O connections. Three configurations are available as standard providing 20 input, 20 output or 10 input and 10 output respectively. Isolation of 2.5KVolts is maintained between any two I/O points and the IP bus enabling it to be used in a number of demanding applications. Each input will operate with an input current as low as 2ma. With the standard input resistors input voltages of up to 50Volts can be applied allowing the IP-IO20 to be directly connected to plant wiring. Each input line can be programmed to interrupt on change of state. The output lines are individually fed via solid state relays which provide isolation from line to line and from the logic interface. Each output is able to drive up to 100ma continuously with a power rating of 125mW. For more demanding applications extended environmental specification modules are available

LE-362VL-128 - 3.5 inch Embedded VIA Eden 667MHz CPU Miniboard, Integrated SVGA, TTL TFT LCD, TV-out, 3D Audio, LAN, USB 2.0, CFC and PC/104-plus Interfaces.with onboard 128MB SDRAM

LE-362VL-128-1GHZ - .5 inch Embedded VIA Eden 667MHz CPU Miniboard, Integrated SVGA, TTL TFT LCD, TV-out, 3D Audio, LAN, USB 2.0, CFC and PC/104-plus Interfaces.with onboard 128MB SDRAM with 1GHz processor

LE-362VL-P - 3.5 inch Embedded VIA Eden 667MHz CPU Miniboard, Integrated SVGA, TTL TFT LCD, TV-out, 3D Audio, LAN, USB 2.0, CFC and PC/104-plus Interfaces. No on-board memory.

LE-362VL-P-1GHZ - 3.5 inch Embedded VIA Eden 667MHz CPU Miniboard, Integrated SVGA, TTL TFT LCD, TV-out, 3D Audio, LAN, USB 2.0, CFC and PC/104-plus Interfaces. No on-board memory.with 1GHz processor

PMC 100Fx - 100BaseFX via Multi-Mode or Single Mode Fibre (Fiber), 32 bit PCI from DC to 33MHz PCI 2.2 Compliant, supports 5.0V or 3.3V PCI Signalling Environments, Magic Packet™ wake up without PCI clock, optional Boot PROM, four LEDs that can be programmed to indicate link status and activity

PMC 100Tx - High speed Ethernet interface controller operating at 10 or 100 Mbits/sec. 32 bit PCI from DC to 33MHz PCI 2.2 Compliant, supports 5.0V or 3.3V PCI Signalling Environments, 100BaseTX Magic Packet™ wake up without PCI clock, optional Boot PROM, four LEDs that can be programmed to indicate link status and activity

PMC CF2 - A PMC carrier for two CompactFlash modules providing up to 1Gbytes removable non-volatile storage. On-board PCI to IDE controller with IDE port available via rear I/O connector. Provides removable storage and boot capability for many operating systems

PMC CTR32 - Eight 16 bit counter / timers with external or internal clock up to 250kHz, external or software control of gate and direction, external output set. Interrupt capability on counter roll-over

PMC CTR64 - Eight 16 bit counter / timers with external or internal clock up to 1.67MHz, external gate and direction control, external output set. Interrupt capability on rollovers, 32 Bits TTL I/O with byte selectable direction and input hold

PMC DIO32 - 32 Bit Opto-isolated I/O available in various combinations of inputs and outputs, programmable input de-bounce timer, Interrupt on change of state, Programmable watchdog timer with interrupt, Independent watchdog output, front or rear I/O connections

PMC DIO64 - TTL level compatible 64 Bit I/O PMC module, Byte selectable as input or output, Inputs latched to 33MHz PCI clock, Interrupt on change of state, Programmable watchdog, Front or rear I/O

PMC FW2 - Three port 1394 Firewire PMC module using Texas TSB12LV26 IEEE1394 OHCI compliant Host controller and TSB41AB3, three port transceiver/arbiter compatible with IEEE1394a-2000, cable supplied via PCI 12V power via a solid state fuse

PMC SATA - 14 x ISA slotsDaul Channel Serial ATA PMC Controller with conduction cooling capabilities

PMC SCU160 - 64bit/66MHz PMC module supporting SCSI transfers up to 160Mbytes/sec, auto-sensing LVD or SE termination, On-board flash for BIOS and SDMS, Windows,VxWorks and Solaris with Boot support

PMC SCU2 - Uses 53C895 Wide Ultra 2 SCSI LSI Logic SCSI controller, up to 80MB/sec, supports wide and narrow SCSI, auto detection of LVD or single ended SCSI, active SCSI termination, drives up to 12m cable, Flash BIOS, Windows,VxWorks and Solaris with Boot support

PMC SCU2A. - Uses 53C895A Wide Ultra 2 SCSI LSI Logic SCSI controller with extra large 944 byte FIFO, up to 80MB/sec, supports wide and narrow SCSI, auto detection of LVD or single ended SCSI, active SCSI termination, drives up to 12m cable, Flash BIOS, Windows,VxWorks and Solaris with Boot support

PMC SIO4 - Same as PMCSIO8 but with 4 channels

PMC SIO8 - Octal RS232 or RS422/485 16C950 UARTs (high performance version of 16550 with 128byte FIFOs), RS232 up to 1M baud with an 8 signal interface, RS422/485 up to 12M baud with 4 signal interface, all channels available via front panel SCSI-II style connector and via PMC P4 connector for rear I/O

PMC-SCU161 - 64bit/66MHz Ultra160 PMC SCSI module featuring LSI53C1000 controller and conduction cooling. I/O is via a 68 pin SCSI III style D connector.Flash BIOS, Windows,VxWorks and Solaris with Boot support

PMC-SCU162 - 64bit/66MHz Dual channel Ultra160 PMC SCSI module featuring LSI53C1010 controller and conduction cooling. I/O is via a 68 pin SCSI III style D connector and the P4 rear I/O connector.Flash BIOS, Windows,VxWorks and Solaris with Boot support

PMC-SCU82 - Wide Ultra 2 Dual Channel SCSI PMC module featuring LSI53C896 controller and conduction cooling. I/O is via a 68 pin SCSI III style D connector and rear I/O P4 connector.Flash BIOS, Windows,VxWorks and Solaris with Boot support

RP2000 - 68302 Stand-alone CPU Module with Fieldbus Connectivity The RP2000 is a stand-alone CPU module for embedded applications or DIN rail mounting. It features a 68302 Integrated Multi-protocol Processor (IMP) running at 16MHz. Dual serial ports are supplied as standard with a wide variety of I/O available by the addition of plug-in IndustryPacks™. The RP2000 is ideal for applications requiring a modest amount of processing power combined with the ability to tailor the I/O requirements to meet the application. The RP2000 can be mounted on stand-offs or in plastic mouldings for Din rail mounting and to simplify field installation a plug-in connector panel is available, providing screw terminals for each of the 50 way IndustryPack ™ connectors. The opto-isolated RS232/485 serial ports support a wide range of protocols, including FieldLink multi-drop fieldbus networking

WVME-SS - Single-Slot SCSI VMEbus plug-in module

WVME410-016-6 - Ethernet Controller, 16KB SRAM, 6U frontpanel

WVME410-064 - Ethernet Controller, 64KB SRAM, 6U frontpanel

WVME430 - Disc module BVME130, 1.2Gb Wini,2Mb floppy

WVME505 - Watchdog and System Monitor - 3U or 6U (must specify when ordering)